Two used feeder ships make your shortlist for a Finnish winter service. One has a stronger Finnish ice class, but its planned arrival loading leaves its aft draught shallower than the approved minimum. The other sits within its ice draught limits, but its Finnish ice class falls short of the port’s assistance restriction. Each needs a different decision before you commit to the service.
Use this check before signing for a ship intended to call at a Finnish port where icebreaker assistance may be needed. Start with a named port, an expected arrival date and a proposed loading condition. The output is a dated screening decision that the buyer can revisit when the cargo plan or published restriction changes.
1. Establish the ship’s confirmed Finnish ice class
Ask the seller for the ship’s IMO number, current classification certificate and applicable annexes. Use the IMO number when asking the local agent to verify the Finnish ice class with Traficom. The class notation on the certificate is the basis for that confirmation. The guide to ship class notations explains how to read the notation itself.
For confirmation, Traficom lists the certificate of registry, International Tonnage Certificate, International Load Line Certificate and classification certificate. For Finnish ice classes above II, it also calls for the ice class draughts and minimum engine power for the ice class. Those details may appear in the classification certificate or an annex. Record the applicable upper and lower ice waterlines forward and aft, and ask the technical team to verify the power available under any current engine or shaft power limitation. If power availability is unresolved, keep it open in the screening decision. Traficom’s ice class confirmation guidance sets out the evidence to provide.
2. Read the restriction for the port and expected arrival
Open the Baltic Icebreaking Management assistance restrictions and check the Finnish entry for the intended port or area. Save the published restriction and its effective date. Compare the ship’s confirmed Finnish ice class and documented deadweight with the thresholds in the notice. Check for any additional conditions in the notice, including cargo requirements where specified. Keep the ship’s documented deadweight and the cargo quantity in separate fields.
For a purchase decision months ahead of the first call, write down the restriction assumed for screening. Ask the agent to recheck the notice for the actual arrival and whenever the ETA changes. Eligibility is one input to the service plan. The operating team still needs to allow for assistance coordination and waiting time.
3. Check both ends of the ship in the proposed loading condition
Ask the technical team for forward and aft draughts at the start of ice navigation and at arrival, using the proposed cargo, ballast and consumables. Compare each end against its own documented ice limits. A mean draught can sit within the limits while one end falls outside them. Where a loading case needs revision, have the technical team verify the revised case against the ship’s approved stability, strength and other applicable limits. Use the feeder route-fit checklist for the separate berth, cargo and schedule checks.
Worked example: two feeder ships and one Finnish port call
Assume the target port requires Finnish ice class IA or IAS and at least 4,000 tonnes deadweight at the planned arrival. The ships, draughts and port scenario below are illustrative. Both candidates have supplied the relevant class documents and their available power has been checked for this example.
- Candidate A: Finnish IA, 7,200 tonnes deadweight. The port’s class and deadweight thresholds are met. Its planned forward draught is 4.80 m, within the documented forward ice range of 4.60–6.30 m. Its planned aft draught is 4.85 m, below the aft minimum of 5.05 m. The loading case needs revision. Keep the vessel conditional until a technically approved case brings both ends within their documented ice limits.
- Candidate B: Finnish IB, 8,100 tonnes deadweight. The proposed draughts are within the ship’s documented ice limits and its deadweight meets the threshold. The confirmed class falls short of the assumed port restriction. Screen it out for this scenario. Reassess if the target port, timing or applicable restriction changes.
Record the decision before committing to the ship
Keep one line per ship and port call. Record the ship’s IMO number, expected arrival, dated restriction, confirmed Finnish ice class, documented deadweight, power evidence, forward and aft ice limits, planned draughts and the person responsible for each open check. Use three screening outcomes: meets the documented checks, conditional pending evidence or revised loading, and falls short of the assumed restriction. Assign the pre-arrival recheck to the operating team and local agent.
If you are evaluating a ship from our container ship inventory, send the vessel reference, Finnish port, intended arrival window and proposed loading condition so the enquiry starts with the right documents.
Buying, or want a second opinion?
Our sale & purchase desk can help you find, value and inspect the right tonnage. Tell us what you’re looking for and we’ll revert within one working day.